Acer n30 - ActiveSync přes Bluetooth
Pokusil jsem se propojit PDA s PC pomocí ActiveSync přes Bluetooth podle návodu na těchto stránkách.
Bohužel jsem narazil na problém.
Při nastavování v ActiveSync -Connection Settings mi položka Allow serial cable or infrared connection to this COM port: -nabízí pouze COM1 a COM2. širší nabídku nemá. Potřeboval bych aby nabídla přiřazený COM28.
Díky za radu
Bohužel jsem narazil na problém.
Při nastavování v ActiveSync -Connection Settings mi položka Allow serial cable or infrared connection to this COM port: -nabízí pouze COM1 a COM2. širší nabídku nemá. Potřeboval bych aby nabídla přiřazený COM28.
Díky za radu
Kvůli tomu nemusíš zakládat několik témat.
Máš to TADY ;)
Máš to TADY ;)
Activesync berie len po port COM 9
a preto si potrebujes "vyresetovat" porty COM
To sa robi cez regedit.exe
Spustis editor registrov
a nalistujes si >
HKEY_LOCAL_MACHINE -> SYSTEM -> ControlSet001 -> Control
a tam si najdes COM Name Arbiter.
Ked to mas napravo vidis kluc ComDB REG_BINARY
otvor si ho a uprav ho do tvaru>
0000 3F 00 00 00 00 00 00 00 ?.......
0008 00 00 00 00 00 00 00 00 ........
0010 00 00 00 00 00 00 00 00 ........
0018 00 00 00 00 00 00 00 00 ........
0020
ked to bude v takom tvare vsetko zavri a resetni PC a znova si spoj PDA s PC.
a mal by ti naskocit COM 3.
A je po probleme.
a preto si potrebujes "vyresetovat" porty COM
To sa robi cez regedit.exe
Spustis editor registrov
a nalistujes si >
HKEY_LOCAL_MACHINE -> SYSTEM -> ControlSet001 -> Control
a tam si najdes COM Name Arbiter.
Ked to mas napravo vidis kluc ComDB REG_BINARY
otvor si ho a uprav ho do tvaru>
0000 3F 00 00 00 00 00 00 00 ?.......
0008 00 00 00 00 00 00 00 00 ........
0010 00 00 00 00 00 00 00 00 ........
0018 00 00 00 00 00 00 00 00 ........
0020
ked to bude v takom tvare vsetko zavri a resetni PC a znova si spoj PDA s PC.
a mal by ti naskocit COM 3.
A je po probleme.
Na doplnenie !!!
(ak treba -prelozte to niekto prosim -musim odist...)
bezhlave prepisovanie registrov vedie ku katastrofe !!!!!
vlastna skusenost
ja vidim na novonainstalovanom pocitaci ine hodnoty v registroch
a su tam len COM1,COM2
preto takto:
The COM port database for XP/2k is at - HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\COM Name Arbiter
The COM port database consists of a 32 integer array, with each bit (0 or 1) representing
whether a COM port is used.
To make the Bluetooth COM port start at a particular number, user needs to block all COM ports
below that number, install BTW to add the Bluetooth COM ports and reset the COM ports which we blocked.
So for example if you open up this Registry key and look at the "ComDB" element you may see
something like the following:
FF 1F 00 00 ... (NOTE: values are in hex, so change to binary where FF = 11111111, etc)
If you convert the values you see into binary (use the scientific calculator), each 0 or 1
will correspond to a COM port, if its free or used. I have COM ports 1 thru 13 that are used.
My registry looks like
FF 1F 00 00 ...
FF -> 1 1 1 1 1 1 1 1
COM PORT 8-7-6-5 4-3-2-1
1F -> 0 0 0 1 1 1 1 1
COM PORT 16-15-14-13-12-11-10-9
Start from top right and go right to left, top to bottom and see which port is blocked or available.
The key is as follows:
1 is blocked
0 is available.
So to block COM ports until COM 5 and start at COM 6, the registry would be
3F 00 00 00.....
3F -> 0 0 0 1 1 1 1 1
COM PORT 8-7-6-5 4-3-2-1
NOTE: You will need to un-install BTW before doing the registry modification. You will block off port 1 - 5,
install BTW, which should then start at COM 6, then free up COM Ports 4 and 5 so you can use them.
(ak treba -prelozte to niekto prosim -musim odist...)
bezhlave prepisovanie registrov vedie ku katastrofe !!!!!
vlastna skusenost
ja vidim na novonainstalovanom pocitaci ine hodnoty v registroch
a su tam len COM1,COM2
preto takto:
The COM port database for XP/2k is at - HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\COM Name Arbiter
The COM port database consists of a 32 integer array, with each bit (0 or 1) representing
whether a COM port is used.
To make the Bluetooth COM port start at a particular number, user needs to block all COM ports
below that number, install BTW to add the Bluetooth COM ports and reset the COM ports which we blocked.
So for example if you open up this Registry key and look at the "ComDB" element you may see
something like the following:
FF 1F 00 00 ... (NOTE: values are in hex, so change to binary where FF = 11111111, etc)
If you convert the values you see into binary (use the scientific calculator), each 0 or 1
will correspond to a COM port, if its free or used. I have COM ports 1 thru 13 that are used.
My registry looks like
FF 1F 00 00 ...
FF -> 1 1 1 1 1 1 1 1
COM PORT 8-7-6-5 4-3-2-1
1F -> 0 0 0 1 1 1 1 1
COM PORT 16-15-14-13-12-11-10-9
Start from top right and go right to left, top to bottom and see which port is blocked or available.
The key is as follows:
1 is blocked
0 is available.
So to block COM ports until COM 5 and start at COM 6, the registry would be
3F 00 00 00.....
3F -> 0 0 0 1 1 1 1 1
COM PORT 8-7-6-5 4-3-2-1
NOTE: You will need to un-install BTW before doing the registry modification. You will block off port 1 - 5,
install BTW, which should then start at COM 6, then free up COM Ports 4 and 5 so you can use them.